JWSR LLCCall 862-268-2510Call now

Septic tank risers and lids: why add them, and what is involved

A riser brings the tank lid up to ground level, so the tank can be found and serviced without a shovel. Here is what the work involves.

A septic tank riser is a collar that extends the tank's access opening to ground level, topped with a watertight lid. New Jersey's standard, N.J.A.C. 7:9A-8.2, calls for tank manholes to be extended to finished grade with a riser and a removable watertight cover that is bolted or locked. Adding one means digging down to the tank, setting and sealing the riser, fitting the lid, and restoring the yard. JWSR installs and repairs septic systems. We do not pump tanks or perform inspections.

Why add risers and lids

ReasonWhat it means for you
You can find the tankLids on many older tanks are buried, with nothing at the surface. A riser puts the lid at grade, so nobody probes the yard looking for it.
Service does not mean diggingWhen the lid is at ground level, a pumper or inspector opens it and gets to work. When it is buried, someone digs it up first, every time, and the lawn pays for it.
The lid is safe and sealedNew Jersey's standard calls for a watertight cover, bolted or locked so children cannot open it. An old cracked or rotted lid is a safety hazard and lets water into the tank.
It points at the maintenance that mattersN.J.A.C. 7:9A-12.2 puts maintenance on the owner, and names inspection of the tank and scheduled pump-outs. Easy access makes that routine instead of a project.

What New Jersey requires

The state standard for new systems is N.J.A.C. 7:9A-8.2(l), which covers access openings for septic tanks:

  • Each tank, or each compartment of a multi-compartment tank, has at least one access opening, a manhole at least 24 inches square or 24 inches across.
  • Manholes are extended to, and kept at, finished grade by a riser with a removable watertight cover.
  • Covers are bolted or locked so children cannot open them, and are cast iron when the riser is concrete.
  • A permanent, non-corrosive marker goes on the cover or the riser just below it, showing the health department and permit number, the installation date, the system type and the design flow in gallons per day.
  • Inspection ports, four-inch cast iron or PVC with a locked or bolted cap, extend to grade over each inlet and outlet not directly under a manhole.
  • On fiberglass or polyethylene tanks, risers and ports are made of the same material as the tank.
  • After installation, the tank, risers and ports are tested for watertightness (7:9A-8.2(m)).

Those are rules for building a system. Whether an older system has to be upgraded, and whether adding a riser to one needs a permit, is set by your local health department, which administers the rule. N.J.A.C. 7:9A-3.5 requires a permit before anyone repairs or alters a system, so ask them before the work starts.

What the job involves

StepWhat happens
Find and probe the tankIf you do not know where it is, the first job is locating it. A plan from the health department file or the original installation helps. Otherwise it is probing and careful digging, which is also the moment to find any utilities near it.
Dig down to the openingWe excavate around the access opening and down to the top of the tank. Hand-digging near the tank and pipes avoids cracking a lid or breaking a line.
Check what you are attaching toA cracked top, a damaged access opening or a failing lid seat has to be dealt with before a riser goes on. This is a repair, and it can change the scope.
Set the riser and seal itThe riser sits on the access opening and rises to finished grade. The joint has to be watertight. For fiberglass or polyethylene tanks, the rule says the riser must be the same material as the tank.
Fit the lidA removable watertight cover goes on, bolted or locked. With a concrete riser, the rule calls for a cast iron cover.
Backfill and restoreBackfill is placed and compacted, the grade is finished so water runs away from the lid, and the lawn is restored. Keep the lid clear of mulch and landscaping.

It is small excavation compared with the rest of septic work, but it is the same skill: knowing where the tank and pipes are before the bucket goes in. Call 811 before anyone digs, and read the NJ utility damage law if a contractor offers to skip it.

Where this fits with the rest of your system

If you are buying a house on septic, a buried lid is a flag worth raising with your inspector, and septic inspections explains what the report looks at. If the field is the problem, see drain field replacement. For the money side, septic system cost covers what parts cost against a full system. Our septic repair service page covers the work.

Common questions

What is a septic tank riser?

A riser is a pipe-like collar that sits on the tank's access opening and extends up to ground level, so the lid is reachable without digging. Under N.J.A.C. 7:9A-8.2, manholes on septic tanks are extended to finished grade by a riser fitted with a removable watertight cover.

Does New Jersey require septic tank risers?

For systems built to the current standard, yes. N.J.A.C. 7:9A-8.2(l) says all tank manholes shall be extended to and maintained at finished grade by a riser with a removable watertight cover, and each tank or compartment needs at least one access opening, a minimum of 24 inches square or in diameter. Whether an older system has to be brought up to that is a question for your local health department, which administers the rule.

Do I need a permit to add a riser to an existing tank?

Ask your health department. N.J.A.C. 7:9A-3.5 requires a permit before anyone repairs or alters a septic system, but whether adding a riser counts, and what paperwork the town wants, is decided locally. A short call to the office with jurisdiction over your address settles it.

Do the lids have to be locked?

The rule says covers must be bolted or locked to prevent access by children. They must also be designed to keep a watertight seal with the riser, and a permanent marker with the permit number, installation date, system type and design flow in gallons per day goes on the cover or the riser just below it.

What about the inspection ports and the effluent filter?

The rule also calls for a four-inch inspection port to finished grade over each tank inlet and outlet that is not directly under a manhole, with a locked or bolted cap. An outlet with an effluent filter has to be directly under a manhole or have a port that allows at-grade access to the filter, so it can be maintained without entering the tank.

Can you pump or inspect my tank while you are there?

No. JWSR installs and repairs septic systems and does the excavation. We do not pump tanks and we do not perform septic inspections. A riser makes both of those easier for whoever you hire.

How much does adding risers cost?

It depends on how deep the tank is, how many openings it has and whether the lid or top needs repair, so we do not quote a number here. There is no charge to estimate a job you already know you want done. If we have to find the problem first, that is a paid visit.

Code and source references

Treat this as background, not a ruling on your property. Your local health department decides what applies at your address under N.J.A.C. 7:9A, so ask them before the work starts.

How it works

Three steps, no runaround

Step 1

Call or send the form

Call us at 862-268-2510, or tell us about the job online. Emergencies jump the line.

Step 2

Free estimates when you know what you want done

We look at the ground, tell you straight what it needs, and give you a fair, upfront price. When we have to find the problem or design the fix (camera inspection, site evaluation, design), that's a paid visit, credited toward the job if you hire us.

Step 3

We do the work

Markouts and permits handled. We dig, backfill, restore, and walk the finished job with you.

Licensed & insuredLicensed NJ home improvement contractor (HIC #13VH11072100), fully insured.
Local & family ownedBased in Hamburg, NJ
Working in the area since 2016Our own crews and equipment
811 called every jobWe wait for the marks before digging
5.0 on Google111 reviews
Recent work

Real jobs by our own crew

Excavator bucket working an open trench beside a blue pipeWorker standing inside a round excavated hole in soilTrench in a yard with a machine bucket and piles of soilGreen lawn with shrubs and a mulch bed beside a walkwayElectric meter and a small white control box on house siding, with garden hoses on the mulch belowVertical pipe set in a gravel bed inside an excavated pit

See all our work →

Tank lid buried or cracked?

Call 862-268-2510 and tell us what you are seeing. If you know what you want done, the estimate is free.

Call 862-268-2510
Get an estimate

A minute of details now means we can price the work and book the visit without calling you back for them.

Not sure what's wrong? Tell us what you're seeing and we'll tell you what we think.

What happens next
  1. We aim to call you back within the hour.
  2. We ask a few questions and set a time.
  3. You get a written price. It's free when the job is defined. If we need to diagnose first, that's a paid visit, credited toward the job if you hire us.

No obligation. Or call 862-268-2510.

Call 862-268-2510Get an estimate